TEST_PAGE
| ANSI CAMI (Grit) | FEPA (P PAPER GRADE) | Micron μm Nominal |
|---|---|---|
| 12 | P12 | 1815 |
| 16 | P16 | 1324 |
| 20 | P20 | 1000 |
| 24 | P24 | 750 |
| 30 | P30 | 630 |
| 36 | P36 | 525 |
| 40 | P40 | 400 |
| 50 | P50 | 325 |
| 60 | P60 | 260 |
| 80 | P80 | 200 |
| 100 | P100 | 160 |
| 120 | P120 | 125 |
| 150 | P120 | 93 |
| 180 | P180 | 76 |
| 220 | P220 | 68 |
| P240 | 58 | |
| 240 | P280 | 52 |
| P320 | 46 | |
| 280 | ||
| P360 | 39 | |
| 320 | P400 | 35 |
| P500 | 30 | |
| 360 | P600 | 25 |
| 480 | P800 | 22 |
| 500 | P1000 | 18 |
| 600 | P1200 | 14 |
| P1500 | 12 | |
| P2000 | 10 | |
| 800 | ||
| 1000 | P2500 | 8 |
| P3000 | 7 | |
| 1200 | ||
| P5000 | 5 |
Content:
-Test
-Test
AMBIENT MOUNTING - Polyester
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Technovit 4000 | 3 components | -Cures rapidly. -Low shrinkage. -Excellent edge retention. -Excellent abrasion resistance. -Excellent flow behavior. | Opaque | 10 min | 122 °C | Yes |
| Technovit 4002 IQ | 2 components | -Cures rapidly. -Low shrinkage. -Excellent edge retention. -Excellent abrasion resistance. -Excellent flow behavior. | White | 15 min | 99 °C | No |
AMBIENT MOUNTING - Acrylic
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Technovit 4006 | 2 components | -Longer polymerization time. -Good for sensitive material. -Excellent for visual inspection. -Reduced the polymerization heat by -10%. -Reduced shrinkage. Routine preparation. | Transparent | 9-12 min | 99 °C | No |
| Technovit 4004 | 2 components | -Cures rapidly. -Some shrinkage. -Good edge retention. -Variable mixing ratio. -Routine preparation. | Transparent | 9-12 min | 99 °C | No |
| Technovit 4021 | 2 components | -Reduced shrinkage. -Good edge retention. -Cures rapidly. -Less pollutant. -Low viscosity. -Odorless. -Fewer air bubbles. | Black | 5-6 min | 99 °C | No |
| Technovit 5000 | 2 components | -Cures rapidly. -Some shrinkage. -Homogeneous conductive. -SEM / Probe compatible. | Copper | 8-10 min | 125 °C | No |
| Formula 1 | 2 components | -Cures rapidly. -Some shrinkage. -Good edge retention. | White transparent | 9-12 min | 71 °C | No |
AMBIENT MOUNTING - Epoxy
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Epoxy | 2 components | -Cures slowly. -Excellent edge retention. -Excellent abrasion resistance. | Transparent | 24 hours | 90 °C | No |
| Technovit Epox Fast | 2 components | -Infiltrate porous material. -Excellent edge retention. -Excellent abrasion resistance. -Variable cure time. | Transparent | 10 hours | 57 °C | Yes |
| Technovit Epox Regular | 2 components | -Infiltrate porous material. -Excellent edge retention. -Excellent abrasion resistance. -Variable cure time. | Transparent | 18 hours | 35 °C | Yes |
COMPRESSION MOUNTING –Thermosetting - Epoxy Powders
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Epoxy | 1 component | -Very hard. -Excellent edge retention. -Best infiltration. -Low shrinkage. -Resistant to chemical attack. | Black | 8-10 min. | 150-180 °C | No |
COMPRESSION MOUNTING –Phenolic
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Phenolic, Red | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. -Can be used as filler. | Red | 8-10 min | 150-177 °C | No |
| Phenolic, Black | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. -Can be used as a filler. | Black | 8-10 min | 150-177 °C | No |
| Phenolic, Green | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. -Can be used as a filler. | Green | 8-10 min | 150-177 °C | No |
| Phenolic, Brown | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. -Can be used as a filler. | Brown | 8-10 min | 150-177 °C | No |
COMPRESSION MOUNTING – Phenolic Preforms
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Phenolic, Red | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. | Red | 8-10 min | 150-177 °C | No |
| Phenolic, Black | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. | Black | 8-10 min | 150-177 °C | No |
| Phenolic, Green | 1 component | -Routine preparation -Rapid. -High shrinkage. -Fair edge retention. -Not resistant to chemical attack. | Green | 8-10 min | 150-177 °C | No |
COMPRESSION MOUNTING – Thermosetting - Diallyl Phthalate powders
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Diallyl Phthalate, Fibreglass | 1 component | -Excellent edge retention. -Low shrinkage. -Resistant to chemical attack. | Blue | 8-10 min | 130-190 °C | No |
| Diallyl Phthalate, Mineral | 1 component | -Excellent edge retention. -Low shrinkage. -Resistant to chemical attack. | Blue | 8-10 min | 130-190 °C | No |
| Technotherm 2000, Fiberglass | 1 component | -Good edge retention. -Low shrinkage. -Resistant to chemical attack. -Resin is Inorganically filled. -Excellent filling behaviour. -No hazardous components. | White/Grey | 10-15 min | 160-180 °C | No |
COMPRESSION MOUNTING – Thermosetting - Conductive
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Technotherm 3000 | 1 component | -Graphite filler. -Electrically conductive. -Low shrinkage. -SEM/electropolishing | Black | 10-15 min | 160-180 °C | No |
COMPRESSION MOUNTING – Thermoplastic powders
| Product | System | Properties | Colour | Time | Exothermic peak | Use with a pressure vessel or vacuum system |
|---|---|---|---|---|---|---|
| Thermoplastic | 1 component | -Routine preparation. -Fair edge retention. -Not resistant to chemical attack. -Excellent for visual inspection. | Transparent | 12-15 min | 140 °C | No |